Electrical Accessories

CK1101 - 1 Amp. Diodes (2 pak)

When connected in series with a dc load such as a locomotive engine, these diodes will have a voltage drop of 0.7 volts each. Two connected in series will drop 1.4 volt, even with a varying voltage applied to the engine. This configuration provides an ideal, unchanging voltage for any 1.5 volt bulb connected across the diode pair. A safe and inexpensive light source for our popular GRS100 and 200 series of micro bulbs.

CK1101

GRS906 - 2-Pin Micro Connectors (1pr. w/5" wires)

Click Here

The GRS906 consists of one female pair and one male pair of connectors with attached color coded wires. Excellent for wire interconnects in tight places. Gold plated.

GRS906

GRS907 - 2-Pin Micro Connectors (2 pr. w/o wires)

Click Here

Same as GRS906 but without wires. Makes either a male or female connector. Insulating heat shrink tubing pieces included.

GRS907

Battery Holders

Click Here

These battery holders accommodate a wide range of battery sizes and provide numerous output voltage and current configurations. They allow multiple options for battery power applications. A special design locks each battery firmly in place. 18" wires.

A. CK211-7 "AA" Battery Holder, 8 Cell, 12V
B. CK211-2 "D" Battery Holder, 2 Cell, 3V
C. CK211-1 "C" Battery Holder, 2 Cell, 3V
D. CK211-8 9-Volt Clips (2 pak)
E. CK211-6 "AA" Battery Holder, 1 Cell, 1.5V
G. CK211-4 "D" Battery Holder, 1 Cell, 1.5V
H. CK211-5 "C" Battery Holder, 1 Cell, 1.5V
I. CK211-3 "AAA" Battery Holder, 2 Cell, 3V

Black Heat Shrink Tubes

Click Here

A. CK1033-6 Black Heat Shrink Tubes 3/16" I.D.(6 pak)
Use these larger heat shrink tubes for interconnecting heavier gauge wires. Each tube is black in color, measures approximately 1" in length and shrinks to 1/2 the original size when heated.Used typically with 18 gauge size lamp cord wire.

B. CK1033-5 Black Heat Shrink Tubes, 3/32" I.D.(6 pak)
Used typically with 20 gauge wire (i.e.,CK1008 series of lead - in wires)

C. CK1033-4 Black Heat Shrink Tubes, 1/16" I.D(6 pak)
Used typically with 24 gauge wire (i.e., CK203-1 speaker type wire)

CK1102 - Flanged Spade Lugs, Insulated (6 pak)

Click Here

The CK1102 spade lugs may be attached to a wide range of 18-24 gauge wire sizes and used for connecting wires either to transformer or terminal block screws. Designed for either crimping or soldering to stripped wires.

CK1102

CK1026 - Fuseholder

Click Here

Use this handy fuseholder wherever layout protection is required. Suitable for all 1/4" X 1-1/4" fuses. Connection instructions included. Measures 1/2" X 2-1/4".

CK1026

Fuses

Click Here

1/2, 2 and 4A Fuses
These high-speed fuses give instant protection wherever they are used. Condition may be determined by visual inspection through the glass. Measure 1/4" X 1-1/4".

CK1048 - In-Line Switch

Click Here

Use this switch wherever on/off power control is desired. It may be used on either 12 or 115 volt lines with zip-type cords between 16 and 20 gauge. No soldering; only a screwdriver and wire cutter are required for assembly. To connect, disassemble the switch, cut a segment from one conductor, install wires in switch, and reassemble. Sharp teeth inside the switch make the necessary electrical contacts. This is the same switch as used on the CK1008 series of lead-in wires. Measures 1-1/4" X 5/8".

CK1048

CK1048-1 - Small Slide Switch

Click Here

Our small slide switch is well suited to any layout application requiring simple on/off control. Measures 5/8" long by 3/16" wide by 3/8" deep.

CK1048-1

CK1033-1 - Solder Spool

Click Here

Use this high-quality solder in conjunction with our CK1053 soldering iron for all your soldering needs. The 60% tin, 40% lead alloy composition assures a low melting point and strong metal-to-metal contact. Convenient dispenser pack.

CK1033-1

Teminal Blocks

Click Here

Two, Four and Six-Pole Terminal Blocks.
Use these heavy-duty terminal blocks for interconnecting wires of all sizes. Electrical connection exits between opposite screw terminals and one or more wires may be attached to each screw terminal. The three different sizes have respective lengths of 1-1/2", 2-1/4" and 3".

A. CK1049 - Two-Pole Terminal Block
B. CK1049-1 - Four-Pole Terminal Block
C. CK1049-2 - Six-Pole Terminal Block

CK1049-4 - Terminal Block Jumpers (6 pak)

Click Here

A convenient method of joining terminal block screws together. These jumpers eliminate the need for running wires between screws when fan-out of incoming wires is desired. Design allows easy installation and removal.

CK1049-4

GRS600 - Ultimate Micro Motor

Click Here

To our knowledge, this is the smallest and most compact motor to be found in the entire hobby industry. If you're looking for a prime mover that can be used in the tightest of quarters, this is the one.The GRS600 Ultimate Micro Motor is not a toy motor, but one built to high industrial standards. Its low-battery current and high efficiency assures a long and maintenance-free life of operation.

Specifications:
Current: 1.5VDC, 35ma
3.0VDC, 120ma
Speed: 12,000rpm (unloaded)
Leads: 1", orange and black
Uses:
1. Working props and spinning jet turbines on model display aircraft.
2. Working props on model boats.
3. Micro scale flying models.
4. Scale machinery such as working saw mills, conveyors, etc.

GRS600

GRS601 - Micro Motor Controller

Our GRS601 controller has been designed for our GRS600 Micro Motor but will work on any 1.5-3.0 volt hobby motor drawing up to 300ma of current. The controller uses pulse modulation to create a wide range of motor speeds. It also incorporates thermal limiting to prevent damage to the unit in the event of a shorted or stalled motor.

GRS601